Tools · Architecture

Smart Roof

Click round the edge of the top floor slab — in Turkey the slab carries the eaves past the walls and the timber roof sits on it, following its edge (a click on the first corner closes it). It resolves the roof for any outline — a rectangle, an L, a T, a U: hips at the outer corners, valleys at the inner ones, ridges where the planes meet. Hipped: every side slopes; gable: the ends of the wings stand as gables; mono: the first side clicked is the low eaves. Then what a carpenter builds: rafters 5/10 @50, hip and valley rafters, a plate on the walls, purlins at most 2.2 m apart, posts on sole plates at most 3 m apart, collars and 45° braces; the tiles over it and the gables filled. Type the pitch (33%) or how far the tiles drip past the slab (50mm). The card checks the pitch against the tiles and says the ridge, the area and the tiles. Sandwich panel on the card makes it a steel roof: IPE rafters, C purlins, panels with their ribs, caps, valley flashings and gutters, counted in panels and kg of steel. Terrace sandwich puts a light roof behind a parapet on a terrace slab: box purlins on box posts, an inner gutter. One group on the tag ARQO Roof, one Undo. From the Library, the roof's sheet: plan, section, details with every part named and the table of members, at 1/50 and 1/10.

How to use it

  1. Start Smart Roof. Press Tab for the form: Hipped (every side slopes), Gable (the ends of the wings stand as gables) or Mono (the first side you click is the low eaves). Choose the covering on the card: tiles, or Sandwich panel for a steel roof (the pitch turns 10 %).
  2. Type the pitch (33%) or how far the tiles drip past the slab (50mm) if you need them.
  3. Click the corners of the top floor slab's edge, one after another. The slab carries the eaves past the walls; the roof sits on it and follows its edge.
  4. The card shows the ridge's height, the roof's area, the tiles and the checks while you go.
  5. Click the first corner again (or press Enter) to close the outline: the roof is built.

Keys

Tab
Hipped, gable, mono
Enter
Close the outline and build
Esc
Take the last corner back

Type in the measurements box

33%
The pitch
50mm
How far the tiles drip past the slab

Good to know

  • Any outline works — a rectangle, an L, a T, a U: hips form at the outer corners, valleys at the inner ones, ridges where the planes meet.
  • The structure: rafters 5/10 every 500, hip and valley rafters 8/16, a plate on the walls, purlins at most 2.2 m apart and a ridge purlin, posts 10/10 on sole plates at most 3 m apart (none on the walls), pairs of collars towards the eaves cut level with the rafters' top, and 45° braces along the purlins. Each member is a closed box, grouped by kind.
  • Tiles: Marseille, Mediterranean, Alaturka or concrete. The pitch is checked against them: no tiles under 20 %, an underlay needed under 30 % (Marseille).
  • One group on the tag ARQO Roof; one Undo removes it. The roof's plan is written on it.
  • Sandwich panel: a steel roof — IPE rafters every 3 m from eaves beams on the slab to the ridge beam and the hips, C purlins every 1.5 m along the slope, beams on box posts where a rafter would run past 5 m, PIR panels (60 mm; 40–120 in the Library) with their ribs, caps over the hips and ridges, valley flashings and a gutter along every eaves. The card counts the panels, the kg of steel, the gutters and downpipes.
  • Its checks: at least 5 % (under 10 % only single-length panels, no end laps); the purlins against the panel's span (a rule of thumb — the supplier's table decides); panels over 12 m split with end laps.
  • The roof's sheet: select the roof, open the Library's Roofs tab and press Make the roof sheet. Beside the roof, on the tag ARQO Roof Sheet: the roof plan with its dimensions, section 1-1 through a truss, the details at 1/10 (eaves, ridge, post head, post foot) with every part named and its size, and the table of members with m³ of timber or kg of steel. Changed from the Library, the sheet follows the roof.
  • Terrace sandwich: on a terrace slab behind its parapet (click the parapet's inner face) — 50 PU panels inside it, box purlins on box posts on base plates, an inner gutter at the parapet's foot; no rafters or gable walls.

Always

  • One Undo takes the whole action back.
  • Shared components: you choose this copy or all copies.
  • The result is told in plain words; a refusal changes nothing.